This is the Bill of Materials (B.O.M.) for the Shapeoko 2. To see the B.O.M. for the SO3, see B.O.M., c.f., the Shapeoko 3 page.
Detailed information, ordering links, and where appropriate, links to overview or sub-pages about specific parts, is available on the Parts page.
ShapeOko 2 Mechanical Kit
Sortable table
Part #
|
Description
|
Quantity
|
25202-01
|
Delrin V-Wheels
|
20
|
25196-01
|
5x16x5mm Bearings
|
52
|
25201-01
|
Precision (Shim) Washers
|
26
|
25197-01
|
Smooth Idler Wheel (Drum)
|
6
|
30158-01
|
Eccentric Nut
|
10
|
PS20004
|
M5 x 20mm Button Head Cap Screw
|
18
|
25287-02
|
M5 Flat Washer
|
110
|
25284-02
|
M5 Hex Nut
|
26
|
25286-05
|
M5 x 30mm Button Head Cap Screw
|
10
|
25312-14
|
3/8" x 5/16" x #12 bore Aluminum Spacer
|
10
|
26029-01
|
Motor Mount Plate (12ga)
|
4
|
30287-01
|
Spindle Mount Plate (12ga)
|
1
|
PS20010
|
13mm x 35mm x 20mm Delrin Lead nut
|
1
|
PS20012
|
Universal Spindle Mount
|
2
|
25286-02
|
M5 x 12mm, BHCS
|
30
|
PS20013
|
Universal Spindle Mount strap
|
2
|
PS20005
|
M5 x 45mm, SHCS
|
4
|
25142-07
|
Z Axis Rail MakerSlide Extrusion 200mm
|
1
|
25772-02
|
Z-Axis Flexible Coupler 5mm--8mm bore
|
1
|
30288-01
|
Z-Axis Motor Mount Plate (12ga)
|
2
|
30169-01
|
8x22x7mm flanged bearing
|
1
|
30289-01
|
Z-Axis Shim Plate (12ga)
|
1
|
PS20011
|
M8 x 1.25mm Threaded Rod Stainless Steel, 200mm
|
1
|
PS20014
|
Brass Standoff spacer M3 male x M3 female 50mm
|
3
|
PS20016
|
5mm x 10mm x 1mm thick, Nylon Spacer
|
4
|
PS20015
|
3mm x 8mm x 1mm thick, Nylon Spacer
|
6
|
25285-10
|
M3 x 12mm, SHCS
|
3
|
25287-03
|
M3 Flat Washer
|
3
|
PS20007
|
M8, Hex Nut
|
2
|
PS20017
|
Wave Disc Spring, .901" ID, 1.159" OD, .013" thickness
|
1
|
26016-01
|
M5 insertion nut
|
26
|
25286-01
|
M5 x 10mm, BHCS
|
12
|
PS20002
|
3/8" x 1-1/4" x #12 bore, Aluminum Spacer
|
6
|
PS20006
|
M5 x 70mm SHCS
|
6
|
25312-20
|
3/8" x 1" #12 Bore, Aluminum Spacer
|
6
|
PS20003
|
M5 x 8mm, BHCS
|
6
|
26051-01
|
Fiberglass Clip
|
6
|
PS20008
|
X/Y Axis Rail MakerSlide Extrusion 500mm
|
4
|
26028-01
|
End Plate (12ga)
|
4
|
PS20001
|
MDF wasteboard (1/2")
|
2
|
PS20009
|
20mm x 20mm x 550mm aluminum extrusion, black anodized
|
2
|
ShapeOko 2 Full Kit
The default configuration is listed in the left-most column below for the tables which depict optional configurations. Some tables include an additional informational column which affords information on which Steps the part is assembled during, and which sub-assembly it is used for.
ShapeOko 2 Controller
Part
|
3-axis CNC milling (default)
|
3-axis Combination milling and 3D printing
|
Controller board
|
25063-02 Arduino x 1
|
Microcontroller:AzteegX5mini
|
Stepper driver board
|
25368-02 gShield x 1
|
USB Cord
|
30314-01 x 1
|
Micro USB to USB cable
|
ShapeOko 2 Wiring
Sortable table
Part #
|
Description
|
Step --- Sub-Assembly
|
Quantity
|
25305-01
|
Stepper Cable
|
|
Lengths:
|
25306-01
|
Terminal Blocks (2x4 type)
|
Used in Wiring Option #2
|
3
|
|
M3 x 16mm, SHCS
|
Used in Wiring Option #2 to fasten the Terminal Blocks
|
6 (or more)
|
25287-03
|
M3 Flat Washer
|
Used in Wiring Option #2 to fasten the Terminal Blocks
|
12 (or more)
|
25284-03
|
M3 Hex Nut
|
Used in Wiring Option #2 to fasten the Terminal Blocks
|
6 (or more)
|
30313-01
|
Power Pigtail
|
|
1
|
ShapeOko 2 Cable Management
Sortable table
Part #
|
Description
|
Step --- Sub-Assembly
|
Quantity
|
25977-02
|
Black expandable sleeving 1/4"
|
|
2 feet
|
25977-04
|
Black expandable sleeving 3/4"
|
|
4 feet
|
25971-02
|
Heat Shrink Tubing 1/4"
|
|
1
|
25971-04
|
Heat Shrink Tubing 3/4"
|
|
1
|
ShapeOko 2 Electrical
Note: The stock power supply will not support heating up a hot end for 3D printing --- you'll need to source a suitable power supply if doing more than basic milling w/ NEMA17 motors.
Part
|
110VAC
|
220VAC
|
Power Supply
|
25309-01 Power Supply 110VAC x 1
|
Power Supply 220VAC x 1
|
PS Cord
|
25320-01 PS Cord x 1
|
PS Cord x 1
|
Tooling
Part
|
110VAC
|
220VAC
|
Spindle
|
30310-01 Spindle 110VAC x 1
|
Spindle 220VAC x 1
|
ShapeOko 2 Motors
Z-Axis
X- and Y-Axes
Part
|
NEMA 17 and GT2 (default)
|
NEMA 23 and GT2
|
Stepper Motor
|
25253-01 NEMA 17 Stepper Motor x 3
|
NEMA 23 Stepper Motor x 3[1]
|
Mounting hardware
|
Direct mounting w/ provided holes:
- 25285-08 M3 x 8mm x 12
- 25287-03 M3 Flat Washer x 12 (or more)
|
While holes are provided, spacing is needed to allow for idler wheel bolts (unless one grinds the bolts down to allow things to fit --- if one did so, one could use shorter bolts, another option is to use a stack of washers rather than the spacers).
- Spacers #12 x ¼” Long x 12
- M5 x 20mm, SHCS x 12 (If BHCS are used, these must be low profile or they will hit other parts and have to be ground down)
- Flat Washer, M5 x 12
- Hex Nut, M5 x 12
|
Pulleys
|
26054-01 GT2 pulleys 5mm bore x 3
|
26054-03 GT2 pulleys 1/4" bore x 3
|
Belting
|
26053-01 GT2 belting
- 500mmx500mm: 6 feet (5 feet will just barely work)
|
26053-01 GT2 belting
- 500mmx500mm: 6 feet (5 feet will just barely work)
|
Sortable table
Part #
|
Description
|
Quantity
|
30312-01
|
Toolkit (compare with Tools)
|
1
|
30311-01
|
Threadlock (see entry under Tools and the assembly instructions)
|
1
|
Size Options
Please compare with Scaling Up.
X,Y
Size
|
Frame
|
Wasteboard
|
Wiring
|
Cable Management
|
Belting
|
500mmx500mm (default)
|
PS20009 20mm x 20mm x 550mm aluminum extrusion, black anodized x2
PS20008 X/Y Axis Rail MakerSlide Extrusion 500mm x4
|
PS20001 MDF wasteboard (1/2") (2)
|
25305-01 Stepper Cable 15 feet
|
Various:
25977-02 Black expandable sleeving 1/4" 2 feet
25977-04 Black expandable sleeving 3/4" 4 feet
25971-02 Heat Shrink Tubing 1/4" x1
25971-04 Heat Shrink Tubing 3/4" x1
|
26053-01 GT2 belting 6 feet (5 feet will just barely work)
|
1,000mmx1,000mm (Inventables)
|
Aluminum Extrusion (40mm x 40mm) - Clear x5
X/Y Axis Rail MakerSlide Extrusion 1000mm x4
Extrusion Bracket (Gusset) (×6)
Pre-Assembly Insertion Nuts[2]
(A sturdy base may be needed at this size, a torsion box is suggested)
|
Inventables: 30300-03 1000mm 1000mm 3/4" MDF
|
25305-01 Stepper Cable 25 feet (20 ft.? approx. --- 15ft for original, plus 500mmx3)
|
Drag chain (pick an appropriate size and lengths, make arrangements for securing it at the ends and fashioning cable tray(s))
|
26053-01 GT2 belting 15 feet[3] (6ft. plus 500mmx3 ~= 11 ft. --- if buying a full kit, the 6ft. in it should cover the X-axis, leaving 8ft. the dual-Y (7ft. will just barely work)[4])
|