Touch Plate v2

From ShapeOko
Jump to: navigation, search

How to make a good touch plate

Making a good touch plate is fairly simple, as long as you can do basic soldering. :)

The instructions below show you how.

Touch Plate-Finished cable-1.jpg

List of materials

The full list of materials you'll need are:

Touch Plate-Raw materials-1.jpg

That photo is missing the 3.5mm TRS audio jack by mistake. :(

Detailed steps

A touch plate is made up of a cable piece which has the actual touch plate on it, along with a jack section connecting the cable to the Shapeoko electronics.

  • The cable piece consists of the touch plate holder, touch plate contact material, an alligator clip, and a modified audio cable.
  • The jack section consists of an audio jack mounted in the controller enclosure, and the jumper wire connecting this jack to the two probe pins on the Shapeoko controller.

The touch plate holder and the contact material look like this:

Touch Plate-Screenshot3.jpg

1. Create the contact material

For the contact material, use something conductive but reasonably soft so end mills aren't damaged when contacting it. Mine is a piece of copper plate, as seen in the top photo.

http://www.amazon.co.uk/gp/product/B011C8JWT8

The contact piece is 19mm in diameter, to fit neatly in it's holder (the aluminium piece also in the photo). I used this STL for cutting it from a larger piece of copper plate:

File:Touch plate.stl

2. Create the touch plate holder

For the touch plate holder, I used 5mm aluminium from Amazon.

http://www.amazon.co.uk/gp/product/B00BGAVFE8

Use this STL to CNC it:

File:Touch Plate-holder.stl

3. Drill the mounting hole for the jack

You need to create an 8mm hole in the Shapeoko enclosure for mounting the audio jack in. This can be anywhere you want, as long as it gives adequate clearance to the other pieces:

Touch Plate-8mm hole-1.jpg

I used an 8mm drill, but any method for creating it will do.

4. Mount the audio jack in the enclosure

The audio jack comes with a simple screw on piece attached to the back of it. Screw that off, mount the jack in the hole, then screw it back on. The end result should look like this:

Touch Plate-Audio jack outside-1.jpg

Touch Plate-Audio jack inside-1.jpg

5. Solder the jumper wire to the audio jack

The next step is to solder the jumper wire to the audio jack.

Use the two short contact posts - one for each of the jumper wires - and leave the long contact post unused. It doesn't matter which way around you solder the wires to the short posts, as the jumper wire on the other end can plug in either way around. When you're done soldering, it should look something like this:

Touch Plate-Solder the bw jumper wire-1.jpg

It's a good idea to cover the exposed metal surfaces with heat shrink too:

Touch Plate-Heat shrink the jumper wire join-1.jpg

6. Mount the enclosure

Now mount the enclosure, sliding the jumper onto the two "probe" pins on the controller board.

The probe pins are the 3rd and 4th ones from the right most side, as shown in the top photo here:

    http://docs.carbide3d.com/article/21-what-should-the-dip-switches-be-set-to-on-my-shapeoko3-controller-board

It should look like this:

Touch Plate-Jack and jumper hooked up-1.jpg

7. Prepare the audio cable

Next, cut the 2 RCA connectors off from the audio cable. DO NOT cut off the 3.5mm audio plug, as that needs to keep on the cable. ;)

After cutting off the 2 RCA connectors, strip the cable a little ways like the photo below:

Touch Plate-Cut and strip the audio cable RCA ends-1.jpg

8. Drill side hole in the touch plate holder

The touch plate holder needs a small hole drilled in it from the side, for one of the audio cable wires to fit through. I used a 2mm end mill to create the hole. After it's drilled, one of the stripped audio cable wires goes through the hole like the photo below:

Touch Plate-Touch plate prior to soldering-1.jpg

9. Solder the contact material

Solder the touch plate contact material to the wire that fed through the hole in the previous step. Ensure the connection is done well, then super glue the wire and contact material in the holder. Allow to dry.

10. Solder the alligator clip

Lastly, solder the alligator clip to the other stripped audio cable wire. The result should look like this:

Touch Plate-Finished cable-1.jpg

And it's complete. Now go and try it out using bCNC or similar. :)