Difference between revisions of "Assembly step 5"

From ShapeOko
Jump to: navigation, search
(added instructional video)
m (User Submitted Notes)
Line 100: Line 100:
 
==User Submitted Notes==
 
==User Submitted Notes==
 
(This is the section to add your own notes pertaining to this sub-assembly) If you run into a problem or find yourself asking a question, please post the solution here to help the next person who has the same problem/question)
 
(This is the section to add your own notes pertaining to this sub-assembly) If you run into a problem or find yourself asking a question, please post the solution here to help the next person who has the same problem/question)
 +
 +
'''Instructables build images'''
 +
 +
[[File:Step5_0.png|none|400px|thumb|Required parts]]
 +
 +
[[File:Step5_1.png|none|400px|thumb|Motor mount bolts and washers]]
 +
 +
[[File:Step5_2.png|none|400px|thumb|Motor mount side of plate showing bolt/washer detail]]
 +
 +
[[File:Step5_3.png|none|400px|thumb|Bolt, washer, spacer placement]]
 +
 +
[[File:Step5_4.png|none|400px|thumb|V-wheels and idlers]]
 +
 +
[[File:Step5_5.png|none|400px|thumb|Washer and spacer detail]]
 +
 +
[[File:Step5_6.png|none|400px|thumb|Extra washers for motor mount]]
 +
 +
[[File:Step5_7.png|none|400px|thumb|Completed x-axis motor]]

Revision as of 17:05, 23 June 2012

(click the picture to download the PDF file)


Instructions

X-Axis Motor Mount Plate

Before tightening the nema17 motor onto the plate, please watch this video.

This is more of a pre-assembly than a fully contained sub-assembly. You're going to assemble this as shown in the drawing.

Make note of a couple of things:

  • The hole orientation at the top of the plate doesn't matter. I have mine to the left, but they can be to the right (as shown).
  • The bottom set of bolts are the long M5 bolts (55mm)
  • When you tighten the motor into place, do so in an X pattern. You want the face of the motor to be equally pressing against the plate.
  • Don't tighten down the v-wheel bolts. Just loosely thread on the nuts to keep everything together.
  • When you are done with the assembly, set it aside, you'll be bolting this to the next assembly build.

Bill of Materials

Sortable table
Item Qty. Part Num. Title
1 6 SM-H04 M5 Hex Nut
2 2 SM-H01 1/4" Nylon Spacer
3 2 MSK01-04 Eccentric Nut
4 2 SM-H08 M5 x 30mm SHCS
5 1 SM-S01 Mounting Plate
6 2 MSK01-06A Smooth Idler Assembly
7 1 MSK01-09 18 Tooth Timing Pulley
8 4 MSK01-05A v-wheel assembly
9 1 SM-E01 Nema17 Stepper Motor
10 28 SM-H03 M5 Flat Washer
11 4 SM-H14 M3 x 8mm SHCS
12 4 SM-H15 M3 Flat Washer
13 4 SM-H09 M5 x 55mm SHCS
14 4 SM-H02 3/4" Nylon Spacer

User Submitted Notes

(This is the section to add your own notes pertaining to this sub-assembly) If you run into a problem or find yourself asking a question, please post the solution here to help the next person who has the same problem/question)

Instructables build images

Required parts
Motor mount bolts and washers
Motor mount side of plate showing bolt/washer detail
Bolt, washer, spacer placement
V-wheels and idlers
Washer and spacer detail
Extra washers for motor mount
Completed x-axis motor