Difference between revisions of "User:Willadams"

From ShapeOko
Jump to: navigation, search
(ShapeOko 3)
(Communication / Control Program Ideas)
Line 371: Line 371:
 
Z = -41.200
 
Z = -41.200
 
</pre>
 
</pre>
 +
 +
==Vector apps==
 +
 +
GraviT
 +
 +
http://www.neowin.net/news/gravit-10-rc1
 +
 +
https://www.maketecheasier.com/gravit-new-design-tool-for-linux/
 +
 +
http://libregraphicsworld.org/blog/entry/quasado-opensources-gravit-web-based-design-tool
 +
 +
https://www.maketecheasier.com/gravit-new-design-tool-for-linux/
  
 
==Communication / Control Program Ideas==
 
==Communication / Control Program Ideas==

Revision as of 09:38, 25 July 2015

Got tired of seeing my name in red in the recent changes....

I'm a graphic designer who purchased a (used) ShapeOko w/ the intention of automating some woodworking projects and extending my capabilities, esp. hoping to build my own custom brass hardware (and tools) so as to not be limited to what's available for purchase commercially.

I'm an admin on the wiki here, so glad to help out w/ any edits or other issues.

Author of The Rules of ShapeOko.

¼″ Drive Shaft Upgrade

  • ¼″ pulley
  • ¼″ aluminum rod
  • ¼″ flanged bearing (use a tapered reamer to enlarge the hole to 13/16″ so that the bearing fits directly, alternately make a bearing plate out of a dimensionally stable material such as hdPe))
  • 5mm--¼″ coupler
  • 4 7/32″ 1.5″ roll pins and 4 ½″ aluminum spacers (used as motor stand-offs) --- will eventually replace w/ 2″ roll pin
  • 4 M3 screws 50mm long
  • an assortment of washers

Other Upgrades

Since implemented double MakerSlide X-Axis, Acme Screw Z-axis and 1m Y upgrades.

  • drill new holes to rotate X and Y motors 45 degrees --- DONE!
  • drill new holes in X gantry plate to invert belt --- DONE!
  • use 10 1″ spacers for carriage--gantry plate --- DONE! but they wouldn't fit over the nifty new bolts, so had to use pan head screws and only used 6 spacers and an assortment of washers
  • enlarge motor shaft hole in Y motor plate to accommodate moving pulley to outside --- DONE! Will test and see if it needs a thrust bearing or something.
  • use ¼″ music wire and 1 ¼″ steel bar for Y-axis belt anchors --- DONE --- tried single track shelf wall standard instead of music wire --- didn't like it, but spare length of ¼″ aluminum rod worked,
  • use short lengths of single track shelf wall standards for X-axis belt anchors --- DONE --- but a hole needs to be enlarged --- DONE
  • run wiring --- DONE!
  • make a nice enclosure of Lego bricks --- DONE (but see below)
  • dust collection --- pick up Dremel EZ Twist Nose Cap and use it to hold a fashioned dust shoe in place --- DONE!
    99cent dust shoe installed.JPG
  • arrange and secure power cords, secure power strip --- DONE!
  • Go tool shopping (DONE!):
    • 1/16, 2.5mm and 4mm hex keys (36+67+81 @ True Value, but they're not ball end, so must be replaced)
    • fine tip screwdriver ($4.79 @ True Value --- replaced w/ a Starrett 559B)
    • 8mm open end wrench ($4.99 @ Sears)
  • Make nice fitted tool insert for cigar box --- DESIGNED --- just need to puzzle out extruding and differencing the tools ---Puzzled out --- next CAM and milling --- DONE Wfa-so-toolbox.jpg
  • make a nicer fitted insert for the cigar box cut out of basswood and lined w/ flocking and felt --- DONE
Current state, more-or-less

Alternative spindles

Picked up a 1/8" Elaire Corp. collet for a Makita RT070x router --- and a router to match. Working on a mount / dust shoe: http://www.shapeoko.com/forum/viewtopic.php?f=8&t=3658


Harbor Freight ¼″ trim router

Worked up a mount and dust shoe set-up for a Harbor Freight ¼″ trim router:

Wfa-hf-dust-shoe-parts.jpg

Wfa-hf-dust-shoe-mounted.jpg

3D Printer Extruder

mount an extruder:

Notes on wiring up a hot-end: http://numbersixreprap.blogspot.ie/2012/07/hot-end.html

Need:

Wfa-so2-extruder-mounting.jpg

Configuration:


Calibration notes

extruded filament width ~= 0.016" (0.4064mm) -- 0.0175" (0.4445mm)

0.5mm thin wall box (sliced solid) --- wall thickness ~= 0.020" (0.508mm) -- 0.030" (0.762mm) --- the latter number seems to be from mis-aligned layers --- need to tighten up the Z-axis carriage.


Ordbot

Reference: http://www.buildlog.net/wiki/doku.php?id=ord:wiring

http://www.robotronics.com.au/web/ordbot-hadron-what-else-do-i-need-complete-3d-printer

http://www.buildlog.net/forum/viewtopic.php?f=16&t=2484

http://www.buildlog.net/wiki/doku.php?id=ord:slic3er_settings

http://www.buildlog.net/wiki/doku.php?id=ord:software

Materials to try

Tips

Hardware to try

Remaining things to do:

Drag knife http://www.thingiverse.com/thing:176025


Sooner

  • add connectors / wiring to SO1 to match Ordbot
  • work out management for Makita power cord and vacuum hose --- build handle arrangement using hanger fixtures and strapping, use pipe or closet rod for handle
  • figure out how to invert belts on X-axis --- probably will do this by getting M5 hex bolts and grinding off a side so that they fit snugly against the side of the motor
  • make a nicer enclosure of Lego bricks --- need to hide away the wires for the p.s. and fan inside the enclosure DONE --- TODO add transparent bit for power LED, add push through stick for reset button
  • replace remaining nylon spacers w/ metal, use 2″ 7/32″ roll pins as stand-offs for Y-axis motor (replacing 1.5″ pins and ½″ aluminum spacers) use 1.5″ pins on spindle mount

Later

  • drill new holes in X gantry plate for second pair of bolts
  • sound enclosure
  • replace standard carriage plate w/ steel version
  • replace Z-axis delrin blocks w/ aluminum

Maybe Eventually

  • replace zip ties w/ cable drag chain
  • drill holes and fasten X-axis MakerSlide together or use Kbot3d's Makerslide Joining Clips
  • maybe re-work belt position, maybe use cable clamps instead of zip ties

Done

  • drill new holes for side vice, mount new T-nuts (or use threaded inserts) --- DONE
  • design nicer / larger / roomier / easier-to-install transparency dust shoe --- DONE

Diamond, Circle, Square

Results (w/ Dremel 4000 and short bit)

  • Diamond 1.278, 1.273, 1.277, 1.270 avg. 1.2745 (==1.39194 less runout) ==2.98298mm
  • Circle 1.841″, 1.840, 1.85, 1.842, 1.840, 1.851, 1.2842, 1.840 avg. 1.84325 (==1.9685 less runout) ==3.18135mm
  • Square 1.843″, 1.839, 1.843, 1.838 avg. 1.84075(==1.9685 less runout)==3.24485mm

Observations

  • Mount piece right (nice) side up
  • re-work G-code to cut deeper? Check Z 9.1948/9.0678 total diff 1.651/1.524 7.5438 circle diff 1.1938 6.35 square diff 1.2192 5.1308 --- CHECKED --- Z had wrong setting in Grbl --- FIXED
  • Add orientation marks to code
  • dust shoe tends to collapse --- add a right angle / elbow inset to focus the vacuum where it's needed and provide more structure and direction to the air --- DONE --- run vacuum on lowest setting --- HELPS --- monitor vacuum and turn off / on or increase speed temporarily to clear things

Projects

Enclosure

pocket 3 diam 3.175 depth -2.25 safety 3 surface 0 step over 30% down 1.25 roughing 0 feed 710 plunge 355

profile 4 diam 3.175 depth -5 outside safety 3 surface -2.25 down 1.5 roughing 0 feed 710 plunge 355

Notes

Original Grbl Settings

(This is for the AtomCNC board running Grbl 0.8a)

$0 = 174.98
$1 = 174.98
$2 = 377.89
$3 = 30
$4 = 500
$5 = 500
$6 = 0.10
$7 = 136 !?!
$8 = 15.00
$9 = 0.05

ShapeOko 3

Home/Limit switches --- DONE installed Tim Foreman's nifty kit

Touch plate.

Wireless --- use Raspberry Pi mounted to gantry to control the Carbide Motion Board --- use Bluetooth Wii Remote as pendant

Upgrade XY belts to 9mm --- test / comparison cuts w/ 6mm

Alternative: http://www.thingiverse.com/thing:194586


Work up 3D printed design for centering vise angled table jig? Way to mount workpieces to front of machine at 45/90 degree angles to cut joints?

Work up design for 4th axis, repurposing spare motor for rotational axis --- control electronics?

Grbl settings:

$$
$0=10 (step pulse, usec)
$1=255 (step idle delay, msec)
$2=0 (step port invert mask:00000000)
$3=6 (dir port invert mask:00000110)
$4=0 (step enable invert, bool)
$5=0 (limit pins invert, bool)
$6=0 (probe pin invert, bool)
$10=255 (status report mask:11111111)
$11=0.020 (junction deviation, mm)
$12=0.010 (arc tolerance, mm)
$13=0 (report inches, bool)
$14=1 (auto start, bool)
$20=0 (soft limits, bool)
$21=1 (hard limits, bool)
$22=1 (homing cycle, bool)
$23=0 (homing dir invert mask:00000000)
$24=100.000 (homing feed, mm/min)
$25=1000.000 (homing seek, mm/min)
$26=25 (homing debounce, msec)
$27=5.000 (homing pull-off, mm)
$100=40.15748 (x, step/mm)
$101=40.264567 (y, step/mm)
$102=40.000 (z, step/mm)
$110=5000.000 (x max rate, mm/min)
$111=5000.000 (y max rate, mm/min)
$112=5000.000 (z max rate, mm/min)
$120=400.000 (x accel, mm/sec^2)
$121=400.000 (y accel, mm/sec^2)
$122=400.000 (z accel, mm/sec^2)
$130=425.000 (x max travel, mm)
$131=465.000 (y max travel, mm)
$132=80.000 (z max travel, mm)

$0=10 (step pulse, usec)
$1=255 (step idle delay, msec)
$2=0 (step port invert mask:00000000)
$3=6 (dir port invert mask:00000110)
$4=0 (step enable invert, bool)
$5=0 (limit pins invert, bool)
$6=0 (probe pin invert, bool)
$10=255 (status report mask:11111111)
$11=0.020 (junction deviation, mm)
$12=0.010 (arc tolerance, mm)
$13=0 (report inches, bool)
$14=1 (auto start, bool)
$20=0 (soft limits, bool)
$21=1 (hard limits, bool)
$22=1 (homing cycle, bool)
$23=0 (homing dir invert mask:00000000)
$24=100.000 (homing feed, mm/min)
$25=1000.000 (homing seek, mm/min)
$26=25 (homing debounce, msec)
$27=5.000 (homing pull-off, mm)
$100=40.000 (x, step/mm)
$101=40.000 (y, step/mm)
$102=40.000 (z, step/mm)
$110=5000.000 (x max rate, mm/min)
$111=5000.000 (y max rate, mm/min)
$112=5000.000 (z max rate, mm/min)
$120=400.000 (x accel, mm/sec^2)
$121=400.000 (y accel, mm/sec^2)
$122=400.000 (z accel, mm/sec^2)
$130=425.000 (x max travel, mm)
$131=465.000 (y max travel, mm)
$132=80.000 (z max travel, mm)

Positioning centered at the front of the wasteboard, just above the worksurface:

X = -211.500
Y = -359.000
Z = -41.200

Vector apps

GraviT

http://www.neowin.net/news/gravit-10-rc1

https://www.maketecheasier.com/gravit-new-design-tool-for-linux/

http://libregraphicsworld.org/blog/entry/quasado-opensources-gravit-web-based-design-tool

https://www.maketecheasier.com/gravit-new-design-tool-for-linux/

Communication / Control Program Ideas

Rework: GUIGcodeWriter_1.0.py --- https://drive.google.com/file/d/0B1FDV9G7idL0OE5MVDlCN0NKNTQ/edit?usp=sharing

Potential Toolkits:

To do:

  • collect screen grabs of extant comm/control programs
  • see if GUIGcodeWriter_1.0.py can actually communicate on Windows, Mac OS X and Linux (running on a Raspberry Pi)

Speculation

Thanks. That was all from the wiki though.

This is long and rambling 'cause I haven't had a cup of tea or coffee yet and initially misread the query and I'm not in mood to delete all that I've written. It includes some speculation, 'cause I don't know any more than anyone else, or what has been publicly stated. Hopefully it will be helpful and informative. If not, ignore it.

Sending G-code is a simple process --- you can do it w/ a terminal program, I'd much rather the effort was all unified into a single stack of modular programs, but I guess modern computer architecture doesn't support that.

There was never any real discussion of making Universal G-Code Sender the default, it was a unilateral decision by Edward back when we were doing the SO2 docs. As I've noted elsewhere, I mislike Java, so am biased and try not to say more than that. It certainly works well for people who can run Java on their machines, and has some nice features.

I suspect we may get a new control / code sender program, possibly derived from the Carbide Motion program --- but nothing official has been said to indicate or support this, just that Edward has had better software on his to-do list for a while, and I can't think of anything else which could require so much time.

Tl;dr --- currently I'm most familiar w/ and use http://www.shapeoko.com/wiki/index.php/Grbl_Controller

Remember the old saw:

- good
- cheap
- fast

Pick any two.

That applies here. Most of the opensource options have clunky interface options and weird little difficulties w/ their output. While philosophically, I'd like to limit myself to opensource, I find myself drawing most things in Freehand, simply because nothing else is as efficient and as precise, let alone elegant. If my NeXT Cube was still working, I'd probably still be using Altsys Virtuoso.

Inkscape and MakerCAM and GRbl Controller work for me, albeit w/ the odd crash (running MC locally helps) and the need to trim files after the fact (yeah, it's supposed to happen automatically, I'd rather just do it up front).

Presumably MeshCAM, since it's done by a Carbide3D partner will be well-supported --- it is integrated into and included with their smaller, pre-assembled machine, the Nomad883.

Sig

Ingratitude perverts all the measures of religion and society, by making it dangerous to be charitable and good-natured. --- Thomas Tomkins, [i]Beauties of Writing[/i] 1777